Arrow Building 101 – pt 3

Bowhunting.net
Bowhunting.net
eNews
Bowhunting
& Archery News & Articles



Evaluations
:
Jason Balazs

Last Updated: Feb 22nd, 2007 – 18:37:03

Arrow Building 101 – pt 3

By Jason Balazs

Apr 21, 2006, 00:10

Email
this article


 Printer friendly page


To Jason Balazs web site
Blazin Arrows.

To Part One, and Part Two

Welcome to part three of arrow building, start to
finish.  In the last chapter, Part Two, we went
through the process of fletching our arrows with Flex Fletch Vanes and Gateway
Feathers using the E-Z Fletch from Arizona Rim. 
Then we finished it up, by cutting the shafts to length and installing
the inserts.  During this last
installment I have a few tips for you on aligning your arrows for proper vane
clearance, test the arrows for speed; using the Pro-Chrono PAL from Competition
Electronics, and finish it all off with a pass through test.

Proper Alignment

 One of the most common mistakes that people make when
shooting newly fletched arrows is they do not ?tune? the arrow for the rest
that they are shooting.  I know you might
be thinking, ?Did he say tune??  More
like spin testing the arrow and alignment of the nock.  First, screw in a field point.  Once that is done, find a hard surface and
spin the arrow on the tip, almost like it was a top.  Pay close attention to the area where the
insert meets the arrow.  What you are
looking for is a wobble.  Let?s rephrase
that.  You don?t want to see a
wobble.  If you do notice one, it means
that your insert is not set squarely in the arrow and you might have to re-install
it again.  This is important because if
there is a wobble, it will cause poor arrow flight with broad heads.  Now to align the nock, simply turn the nock ,
using your nock tool, so that there is proper vane clearance through your
rest.  Once you have it where you think
it needs to be, shoot all the arrows at least 4 times each.  After you shoot inspect the fletching for any
kind of contact.  If there is contact,
you might want to turn the nock just a little bit more.  Continue this until you have achieved zero
contact with the fletching.

Nock Tool

Arrow speed

Shooting through chonograph

Now there are a lot of people out there who have excuses
for not wanting to shoot certain types of vanes, arrows, or nocks.  I have heard them all, ?Feathers slow your
arrow,? or how bout this,  ?You need to
use a small nock.? With the bows that are manufactured today, I don?t think
that you need to worry about any of these. 
For this test I used my Diamond Liberty set at 70 pounds with a 29? draw
length, and a Trophy Ridge Drop zone rest. 
I shot an average of 10 shots per each arrow through my chronograph, and
the funny thing is, the feathers were two feet per second faster than the
vanes.  That was 60 shots with the
vane-fletched arrows, and 60 shots with the feather-fletched arrows.  Next, I inserted new nocks that are 30 grains
heavier than normal nocks.  Those proved
only to decrease the speed by one foot per second average.  On average all my shots were ranging 263 fps.  I don?t think that anyone would complain
about their hunting bow shooting that fast.

Pass Thru Test

Through the box into the target


This was conducted by shooting
the arrows that we just fletched through a box (with a target behind it) that I
filled with tightly packed paper. Now when I say tightly packed, I mean tightly
packed.  I was jumping on the paper I was
putting in there and filled it completely. 
I then grabbed an arrow from each lot. 
First I shot the feather-fletched arrow through the box and then the
vane fletched one through.  The arrows
went completely through the box and stuck into my field point target.  You couldn?t tell they had even gone through
the box, so I shot them both 10 more times through.  Even after ten times through, they did not
rip or tear off of the arrows.  Now that
my friends is 100% vane adhesion!

Everything still in place and looking good

Conclusion

I hope that I have been
able to help you learn a few tips and tricks from these last three installments
of arrow building, start to finish.   As
I stated in Part One, it was my pleasure to take on this project for
bowhunting.net. If one thing is true, this process has proven that using the
best equipment made, like the E-Z Fletch, to fletch the top of the line
fletching and feathers to your arrows, is worth every penny.  I look forward to seeing you at the range, or
in the woods!!

Visit Jason?s homepage: www.blazinarrows.com

Below are the links
for the products I used for this project.

 

© Copyright
2004, 2005, 2006 by Bowhunting.net

Top of Page

Sticks N' Limbs Camouflage

The Bowhunting Netcenter

We
invite you
to visit some of the other Bowhunting.net Netcenter web sites: